Question: What Can You Use Instead Of Solder?

Does Gorilla Glue work on copper?

Gorilla Glue (made by Super Glue) works well on metal..

Can JB Weld be used as solder?

A: No. J-B Weld is not considered to be a conductor. It is an insulator. What do you need to solder?

Can I solder without flux?

It’s ok, if you can do it, but it’s very difficult to solder without flux. The flux breaks down the oxide layers on the metal surfaces and allows the solder to “wet” them. If it doesn’t wet, it doesn’t make a connection. … It’s normally always necessary to use flux when you solder.

What metal does solder not stick?

Basically all metals can be soldered, but we are looking for a low melting point soft solder and a flux. With the soft solders and a zinc chloride flux (most common), these metals will bond very easily: copper, tin, and brass. These metals will NOT bond: Iron, stainless steel, steel, and aluminum.

Is aluminum foil electrically conductive?

Aluminum foil is known to be a conductor of electricity, which means that electrons can move freely through the material when a charge is applied to it.

Can I use Vaseline instead of flux?

Can I use a Vaseline instead of flux? This question might just linger in your mind at the moment. The answer is yes. Using petroleum jelly as a soldering flux is an effective soldering flux alternative.

Is there a glue that works like solder?

If you’ve ever soldered or welded, you’ll know that things get pretty hot. MesoGlue intends to fix that. It’s a room-temperature metallic glue that lets you stick parts together with reckless abandon and electrical control.

Is solder stronger than epoxy?

Solder is stronger. JB weld is easier. JB weld is epoxy; it just has a filler that is hard, and made for cheap fixing of castings. JB will be stronger than a bad solder joint so if you cant make a solder joint for nothing, JB will be good.

Can you connect wires without soldering?

What you need: a roll of electrical tape and two wires whose ends have been twisted together. First, lay the twisted part of the wires onto a strip of electrical tape. Wrap the tape around the wires tightly 5-6 times, making sure to cover up all the wire. Give your connection a tug to make sure it is strong.

What can I use if I don’t have flux?

A: The classical fluxes were wood rosin and acid solutions – both intended to protect even etch the top surface when it gets hot and is likely to oxidize. Instead, you can place a puddle of solder on one (horizontal) surface, and with a pen knife blade, scratch the metal under the blob.

Can you melt paper clips?

It is very easy. I loaded the Mod Melts into my high temp glue gun, let it heat up, and then squirted the Mod melts into the mold. I put one end of the paperclip down on top of the mold, and then added a little more Mod Melt on top. Then I waited 10 minutes, and popped out the Mod Melt.

Can you use glue instead of solder?

It is not as good as solder for many reasons but it can be very useful if soldering can not be done normally. Hilanderbob, it really is not. There are no substitutes to soldering. There is no tensile strength with superglue and any time you will use the port it will crack etc.

Can I use aluminum foil instead of solder?

all you need is aluminum foil and eletrical tape. simply connect the wires and tightly wrap them together in aluminum foil. then put eletrical tape around it and there you have it. any ametures(ignore my spelling) like me that dont have a soldering iron can do this.

Can you solder without solder?

Steel wire, screwdrivers, nails, and Alan wrenches are all potential tools for your emergency soldering. Just heat your wire or other steel tool over some open flame for 20-30 seconds and then proceed to solder as you normally would.

Can you use a paperclip as solder?

This common mesh is galvanised steel i.e. steel which has been coated with zinc. Apparently paperclips are also made of galvanised steel as a rule, so there may be a connection here. … Other metals such as aluminium or regular steel can be soldered, but require special solder and flux and may need stronger equipment.

Can a lighter melt solder?

You have a lot of options for this. You can use anything that is able to heat a piece of metal up to the melting point of your solder (between 400°F / 200°C and 700°F / 370°C). Butane lighters work the best. But you can also use candles, oil lamps, alcohol burners, or even open camp fires.